The Armour Archive

These Punchs are in good Working order.
rated at 1.2 ton punching power
1/8 in .120" or 11 guage mild steel
3/16 in .075" or 14 guage mild steel
and 1/4 in .062" or 16 guage mild steel
http://www.roperwhitney.com/tech/chart1.cfm

I will deliver to your camp at Pennsic.
I will ship any where at costs. In the USA its about 5 europe and Austrailia is under 15 for the whitney punch.

Punch Whitney 5JR 50 dolars
Punch sizes are 3/32, 1/8, 5/32, 3/16, 7/32, 1/4, and 9/32
[img]http://img.photobucket.com/albums/v297/losthelm/th_S5030420.jpg[/img]
[img]http://img.photobucket.com/albums/v297/losthelm/th_S5030419.jpg[/img]

Punch Whitney 5JR 45 dolars
Punch sizes are 3/32, 1/8, 5/32, 3/16, 7/32, 1/4, and 9/32
The 9/32 die was dammaged with some chipping on the screw slot I carefully ground down the chipped area and cut a new slot. the last picture shows this Die. I ground this slowly so the hardness/temper of this die is undamaged.
[img]http://img.photobucket.com/albums/v297/losthelm/th_S5030421.jpg[/img]
[img]http://img.photobucket.com/albums/v297/losthelm/th_S5030422.jpg[/img]
[img]http://img.photobucket.com/albums/v297/losthelm/th_S5030424.jpg[/img]

This heat gun I picked up to do some plastic work but I just never liked plastic armour. I cut the seam on the safty lable when it stopped working and replaced the blown capacitor. Milwaukee 3300 auto cool down and digital control 12 temp settings 250-1350 Great Tool.
25 plus shipping
[img]http://img.photobucket.com/albums/v297/losthelm/th_S5030436.jpg[/img]
[img]http://img.photobucket.com/albums/v297/losthelm/th_S5030437.jpg[/img]

Osborn rotary punch this has punches sized 0-5 Great tool for ajusting straps and such.
20
[img]http://img.photobucket.com/albums/v297/losthelm/th_S5030274-1.jpg[/img]

Small jewlers stake with a flaw on one end. it looks like a small line on thei right side. About 4 inches end to end and about 1/2 inch wide.
10
[img]http://img.photobucket.com/albums/v297/losthelm/th_S5030433.jpg[/img]
[img]http://img.photobucket.com/albums/v297/losthelm/th_S5030434.jpg[/img]

Dishing form small divit in the bottom where the sand gave way in the casting process. Its 60/45/15 ductile cast iron from the guy that sold these on Ebay a while ago about 4 inches acrost.
25
[img]http://img.photobucket.com/albums/v297/losthelm/th_S5030428-1.jpg[/img]
[img]http://img.photobucket.com/albums/v297/losthelm/th_S5030430.jpg[/img]
[img]http://img.photobucket.com/albums/v297/losthelm/th_S5030431-1.jpg[/img]

PM sent


-JP

pm sent

and edited the post to remove that one