FS Merctailor Steel Finish, Arms, Besagues & Finger Bucklers

For trading/Selling/and posting items that you need very badly.
Post Reply
AL
Archive Member
Posts: 1978
Joined: Wed Apr 16, 2008 8:16 am
Location: East Rottenchester
Contact:

FS Merctailor Steel Finish, Arms, Besagues & Finger Bucklers

Post by AL »

I have for sale one pair of 14/15th c. arms, one pair of besagues and one pair of finger bucklers all done with steel rather than brass rivets.

The arms are made from 16 gauge steel, with an outwardly rolled top edge rebrace and bracer cuff and beveled plate edges where appropriate. They come fully strapped with hand made buckles and steel holders with light decorative file and chisel work. They have leather tabs at the top of the rebrace with two eyelets for pointing. The bracers turn in slots in the manner of the " Voght of Match " armour in Churburg ( also shown close up in TOMAR ) and all the rest of the plates are slot riveted as well. The bracers are 8 1/8 inches long and have a max circumference of 15 1/2 inches at the fore arm and 10 5/8 inches at the wrist and is adjustable. They fit me fine and i'm thouroughly average with 14 1/2 inch biscepts and arms that are 23 inches from the ball of the shoulder to the wrist. If needed I can sub out a smaller bracer. They bend fully through the range of the arm and have plenty of hyperextension . I'd like to get $165.00 per pair ( less than I used to charge for them with cast buckles and regular non turning bracers ) plus shipping.

The besagues are made from 16 gauge CR steel. They have rolled and counter sunk edges, are slightly convex with a small raised center point peaked. They are leather lined and have pairs of eyelets for pointing. They are 5.5 inches across . I'd like to get $20 plus shipping per pair.

The finger bucklers are made from 16 gauge CR mild steel with rolled and counter sunk edges for strength. They are slightly domed with a small peak at the center. Lined with leather and stuffed with batting to pad the back of the hand. They are adjustable with hand made buckles with light file and chisel work decoration. They measure 5.5 inches across. Like to get $21 for the pair plus shipping.

Feel free to ask question. Paypal, check or MO are fine.
Attachments
steel 14th century arms reduced.jpg
steel 14th century arms reduced.jpg (82.99 KiB) Viewed 288 times
steel 14th century arm single reduced.jpg
steel 14th century arm single reduced.jpg (84.05 KiB) Viewed 288 times
steel 14th century arm inside reduced.jpg
steel 14th century arm inside reduced.jpg (89.36 KiB) Viewed 288 times
AL
Archive Member
Posts: 1978
Joined: Wed Apr 16, 2008 8:16 am
Location: East Rottenchester
Contact:

Re: FS Merctailor Steel Finish, Arms, Besagues & Finger Buck

Post by AL »

More pics:
Attachments
steel finger bucklers reduced.jpg
steel finger bucklers reduced.jpg (76.31 KiB) Viewed 287 times
steel besagues reduced.jpg
steel besagues reduced.jpg (75.86 KiB) Viewed 287 times
spaulder buckle reduced.jpg
spaulder buckle reduced.jpg (23.36 KiB) Viewed 287 times
AL
Archive Member
Posts: 1978
Joined: Wed Apr 16, 2008 8:16 am
Location: East Rottenchester
Contact:

Re: FS Merctailor Steel Finish, Arms, Besagues & Finger Buck

Post by AL »

Bump.
AL
Archive Member
Posts: 1978
Joined: Wed Apr 16, 2008 8:16 am
Location: East Rottenchester
Contact:

Re: FS Merctailor Steel Finish, Arms, Besagues & Finger Buck

Post by AL »

Bump.
AL
Archive Member
Posts: 1978
Joined: Wed Apr 16, 2008 8:16 am
Location: East Rottenchester
Contact:

Re: FS Merctailor Steel Finish, Arms, Besagues & Finger Buck

Post by AL »

Arms are sold.
Post Reply