Leather-armour pattern?

NoStradamuS · Post by **NoStradamuS** » Fri Dec 27, 2002 7:54 am

I`m searching for a pattern to a leather armour... plz help!

------------------
--------------------------
REAL FRIENDS STAB YOU IN THE FRONTâ€¦

CrowÂ´s Anvil · Post by **CrowÂ´s Anvil** » Fri Dec 27, 2002 8:29 am

Hi !

What kind of leather armour do you want to make? For Legs, Arms, Helm, whole torso ?
I have a pattern for a whole leather armor:

[img]http://www.crowsanvil.de/Produkte/Torso/t-ldr-01-m02-k.gif[/img]

but itÂ´s to big to put in on my scanner.
I can give you some sizes if you want...

Chriz

NoStradamuS · Post by **NoStradamuS** » Fri Dec 27, 2002 8:38 am

A whole leather armour would be greate!
I was searching mostly for a pattern to torso, but give me the sizes

--------------------------
REAL FRIENDS STAB YOU IN THE FRONTâ€¦

[This message has been edited by NoStradamuS (edited 12-27-2002).]

Hugo de Stonham · Post by **Hugo de Stonham** » Fri Dec 27, 2002 8:47 am

I would also like the leather armour patterns that you have.

CrowÂ´s Anvil · Post by **CrowÂ´s Anvil** » Fri Dec 27, 2002 11:28 am

so it be, please give me some time (a few hours) to make that, I will be back with the dates !

Chriz

CrowÂ´s Anvil · Post by **CrowÂ´s Anvil** » Fri Dec 27, 2002 4:24 pm

Okay here comes my way:

Please refer to the picture

[img]http://www.crowsanvil.de/Lederruestung.jpg[/img]

I: back piece
II: front piece, need 2 of them (one is mirrored)
III: shoulder piece

Following sizes are needed:
A: from shoulder to bottom : 83 cm
B: from shoulder to waist : 53 cm
C: width : 58 cm
D: shoulder with : 19 cm
E: half with = 1/2 C : 29 cm
F: front cutout (down): 20 cm
G: front cutout (side): 10 cm
H: shoulder plates (main plate)radius : 22 cm
I: shoulder plates (cover piece) radius : 26 cm

I would build it in the following order:
1) cut out the leather
2) sew the edges with soft leather
3) attach buckels: 3 on the front (leave space where the belt will be)to close armor
4) punch the holes on the side; these holes are used to sew the front and the back piece together, I have taken thick leather band to sew them together, I have strenghten the hole via metal eyelets
5) attach buckels: 3 on each side (left and right, they assist the leatherband mentioned in point 4)
6) make shoulder piece: the main plate is made of 5mm thick leather, on that main plate the cover piece (from the same leather as the front and back piece of the armor) is riveted. The cover piece is a little bigger because itÂ´s fringing the shoulder main plate. I have riveted the cover piece from the inside through about 50 holes:

[img]http://www.crowsanvil.de/Produkte/Torso/schulterdetail.jpg[/img]

DonÂ´t forget the leather stripes on both sides to attach the shoulder plate to the buckels (step

at the front and back piece of the armor

7) sew with a thick leather band the front and the back piece (I and II) at the shoulder together, you can also sew the shoulder pieces from the underside onto the torso

attach buckels to tie up shoulder pieces; one front right, one front left, one back right one back left; position belongs to the stripes of the shoulder piece

[img]http://www.crowsanvil.de/Produkte/Torso/lederruestungfront.jpg[/img]

I think we are finished. If I were somewhere not able to describe clearly what you have to do, donÂ´t hesitate to post a reply.
Have fun !

PS: 1 inch is about 2,5 cm

Chriz

[This message has been edited by CrowÂ´s Anvil (edited 12-27-2002).]

losthelm · Post by **losthelm** » Fri Dec 27, 2002 10:13 pm

print up the pattern and put it on the archive.

CrowÂ´s Anvil · Post by **CrowÂ´s Anvil** » Sat Dec 28, 2002 1:50 am

how do I do that ?

NoStradamuS · Post by **NoStradamuS** » Sat Dec 28, 2002 10:33 am

thank you!

------------------
REAL FRIENDS STAB YOU IN THE FRONTâ€¦